Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of PENTAMID A GV30 HYD2 black - PA66-GF30 - Pentac Polymer GmbH

Material Data Center offers the following functions for PENTAMID A GV30 HYD2 black:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Pentamid A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Contracción posterior al moldeo, paralelo 0.4 / * % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.7 / * % ISO 294-4, 2577
Propiedades mecánicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 10300 / 7500 MPa ISO 527
Resistencia a la tracción 185 / 135 MPa ISO 527
Alargamiento a rotura 3.9 / 4.9 % ISO 527
Resistencia al impacto Charpy, +23°C 80 / 90 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 13 / 16 kJ/m² ISO 179/1eA
Propiedades térmicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 260 / * °C ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa 245 / * °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 255 / * °C ISO 75-1/-2
Combustibilidad a 1.5mm esp. nom. HB / * class IEC 60695-11-10
Espesores de probeta 1.6 / * mm -
Otras propiedadesSeco / CondUnidadesMétodo de ensayo
Absorción de agua 5 / * % Sim. to ISO 62
Absorción de humedad 1.5 / * % Sim. to ISO 62
Densidad 1360 / - kg/m³ ISO 1183
Propiedades específicas del materialSeco / CondUnidadesMétodo de ensayo
ISO Data
Indice de viscosidad 140 / * cm³/g ISO 307, 1157, 1628
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 80 °C -
Tiempo de pre-secado 3 h -
Humedad de procesamiento ≤0.13 % -
Temperatura del molde 60 - 100 °C -
Temperatura - zona de alimentación 80 °C -
Zona 1 270 °C -
Zona 2 280 °C -
Zona 3 285 °C -
Zona 4 290 °C -
Zona 5 285 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola, Negro
Resistencia quimica
Estabilidad hidrolitica
Certifications
RoHS
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.